• Cylinder Heads
  • Performance
  • Port and Flow Cylinder Heads

Muscle Car DIY

PERFORMANCE • REBUILD • RESTORATION • MODIFICATION

Automotive Painting Guide: Final Finishing

September 1, 2015 by Muscle Car DiY

This is finally it—the step that makes all that other work worthwhile. Many painters get real satisfaction from learning how to lay down a smooth, glossy, wet coat of paint with no orange peel or runs. But, even for a first-time amateur, seeing that glass-smooth gloss appear from the dull, color-sanded paint after a few passes with a buffer and compound is exhilarating. And it gets even better from there. The rub out with compound is good. But the polish step with a good sealer/glaze is nearly miraculous. And adding a coat of your favorite car wax by hand is frosting on the cake—that you can continue doing for years to keep that shine just as good as new.

 


This tech tip is from the full book, HOW TO PAINT YOUR CAR ON A BUDGET.
For a comprehensive guide on this entire subject you can visit this link: LEARN MORE ABOUT THIS BOOK HERE

 

SHARE THIS ARTICLE: Please feel free to share this article on Facebook, in Forums, or with any Clubs you participate in. You can copy and paste this link to share: https://musclecardiy.com/bodywork/automotive-painting-guide-final-finishing/

 


 

Finally, let’s take a look at this ’60 Pontiac color sanded and rubbed-out by Bill Larzelere. The final rub out, done carefully and properly, is what takes any paint job—done by a pro or done by you at home—from the level of “as good as factory” to full-on custom paint. Anybody who knows cars and knows paint will immediately see the difference. And the best part about this final step is that it doesn’t really cost anything other than a little polishing compound and a few sheets of sandpaper—plus your free time and effort. Yes, you can do all of this, and be proud of it.

 

Even early brush-painted lacquer paint jobs, or those applied with bug sprayers or vacuum-cleaner attachments, can—and have been—color sanded and rubbed out to perfectly smooth and glossy finishes. Things have improved since then. In fact, the chances that you’reusing lacquer paint are slim these days. If, by chance you have acquired and used lacquer paint, including clear, then you must finish the job by rubbing it out, because lacquer does not dry glossy. Lacquer, however, can be hand-rubbed, while most other paints these days can’t be, easily.

Of course, you don’t have to rub out your paint if it’s not lacquer, or if it’s base coat with the requisite clear coat. Nearly all types dry or harden very glossy, and you can leave it that way. Factory paint jobs are not rubbed out. Neither are most body shop jobs. But one thing that truly denotes a custom paint job is the rub out. Even on basic colors like black or red—in fact, especially on such colors—a glass-like rub out makes all the difference. Anybody who knows paint or cars, and most who don’t, see it immediately.

 

There are at least as many ways to color sand and rub out your car as there are ways to put your pants on in the morning. And, given the title and scope of this book, you might think we’d want to show someone doing it at home. But why not show how one of the best does it, so you can learn some tricks? Bill Larzelere, who calls his business “Automotive Grooming” (Burbank, California), has detailed and rubbed out countless Pebble Beach classics and other well-known show winners over the past 30-plus years. Our demonstration subject is a cinnamon red ’60 Pontiac.

 

This low-mileage original needed little more than a new paint job, which the owner had resprayed in base coat/clear coat by a less-than-excel-lent painter. A good rub out person can save a mediocre paint job (to a point). But Bill had partially sanded this one when he realized the hood really needed to be resprayed. Unfortunately, as you can see, it still has plenty of orange-peel in the clear, but this is where we begin to follow the process.

 

In the old days of lacquer, you could color sand it with 600 paper, hand-rub it with paste compound, and you’d be ready for wax. Today’s paints, either 1-stage or 2-stage, generally require color sanding in stages, beginning with 1000-grit and working up to 2500-grit or so. All color sanding should be done wet, and paper for it comes already cut in half-sheets, ready to fold in thirds. The best paper has the most uniform grit.

 

But a couple of caveats: We cover all levels of paint jobs in this book. The color sand and rub out is for the top level. That means you have to do all the preliminary steps fully, and to equal quality, too. This refers primarily to bodywork and block sanding. If you’re going to make the paint surface as smooth as glass, it immediately shows every ripple, dimple, sand-scratch, or any other imperfection that lies underneath it. If you don’t rub out the paint, imperfect preparation won’t show nearly as badly. As usual, it’s your choice.

Rubbing out straight colors (red, yellow, black) is no problem. In fact, I see no reason to put clear coats over them, though people do. On the other hand, while you can rub out metallics, pearls, or candies, it is not recommended without adding a few liberal clear coats first. Paints with micro-particles in them (metallics, pearls) can do weird things when you rub on them, possibly flip-ping-over or “rearranging” those particles. Sanding and rubbing directly on transparent paints (candies) can possibly cause thin spots, which lightens the hue of the color. In both cases, it is much better to sand and rub on a clear coat on top of them, and it is imperative to put enough clear on so that you won’t sand or rub through it at any time during these final steps.

On the other hand, the good part for amateur painters working in home garages, assuming you’ve done the level. That means you have to do all the preliminary steps fully, and to equal quality, too. This refers primarily to bodywork and block sanding. If you’re going to make the paint surface as smooth as glass, it immediately shows every ripple, dimple, sand-scratch, or any other imperfection that lies underneath it. If you don’t rub out the paint, imperfect preparation won’t show nearly as badly. As usual, it’s your choice.

 

Soak your wet-sanding paper at least 30 minutes, to soften it up, before use. Since he does this every day, Bill keeps various grits soaking in labeled, sealed containers in a cabinet in his shop, along with a variety of buffing compounds and polishes.

 

The entire rub out process can be quite messy. For color sanding, many painters keep a dribbling hose in one hand to continually rinse off sanding grit with clean water (if you do, a good tip is to tape around the metal hose end to avoid any paint scratches). I prefer a handy bucket of water to dip the paper in. Either method is best done outside, though hot sun doesn’t help. Bill works inside, and prefers to apply small amounts of water directly to his presoaked paper from a squirt bottle.

 

Most color sanding should be done with some sort of block. Bill cuts a semi-hard rubber squeegee slightly smaller than the folded paper, so he can hold the paper by the edges as he sands in back-and-forth strokes, starting with 1000 grit on this fairly rough paint.

 

Color sanding is basically a visual process. The first step is to sand evenly until all the orange peel disappears. But to see what you’re doing, you must continually clean the surface. Bill, like most, uses a small rubber squeegee to wipe off the water and grit. I like to use a chamois. Or you could even use a towel.

 

He also keeps a spray bottle of water handy to add more, if needed.

 

Here you can see that some of the orange peel remains. The trick is to sand with the 1000-grit until all the shiny areas are gone, and the surface has a uniform satin finish, but not further.

 

Never color sand directly on an edge, corner, or any raised/peaked surface. Sand up to it, as shown here and in the prior photo. If you sand on it, you will immediately go through the clear coat, if not through the paint—guaranteed.

 

In this concave area Bill is using a piece of small, round, pliable sponge rubber as his color-sanding block.

 

But in tight or delicate areas, he also uses his finger(s). Just be careful. Too little is always better than too much at any stage of this process. You can always sand or rub more later (other-wise you can spray more paint).

 

For your first stage of color sanding, you can clearly see when orange peel disappears. But how can you tell how much to sand with 1500 or 2000 paper?The key through the whole sand/rub process is not to go too far at any one stage, so you don’t go through the clear or color coats. One simple way to “see” your sanding progress with the next finer paper is to sand the opposite direction from the prior grit (90 degrees to it). Some use a light dusting of spray paint for a guide coat. Bill’s secret is a thin coat of spray-on graphite, as shown, which not only gives a visual guide but also lubricates the paper at the same time. Ingenious.

 

Rubbing out straight colors (red, yellow, black) is no problem. In fact, I see no reason to put clear coats over them, though people do. On the other hand, while you can rub out metallics, pearls, or candies, it is not recommended without adding a few liberal clear coats first. Paints with micro-particles in them (metallics, pearls) can do weird things when you rub on them, possibly flip-ping-over or “rearranging” those particles. Sanding and rubbing directly on transparent paints (candies) can possibly cause thin spots, which lightens the hue of the color. In both cases, it is much better to sand and rub on a clear coat on top of them, and it is imperative to put enough clear on so that you won’t sand or rub through it at any time during these final steps.

On the other hand, the good part for amateur painters working in home garages, assuming you’ve done the preliminary steps well, is that the color sand and rub out not only removes sorange peel, it also removes small-dust, lint, or even minor surface dirt particles that inevitably get on your garage paint job. If you’re careful, and use a block, you can even sand out minor runs or sags in your final coat.

 

Here you can see that some of the orange peel remains. The trick is to sand with the 1000-grit until all the shiny areas are gone, and the surface has a uniform satin finish, but not further.

 

This is the hood, finish-sanded to 2500-grit, ready for buffing (as is the previously sanded fender). As mentioned in the text, you should thoroughly rinse the surface between each sanding grit, and definitely before you start buffing.

 

With modern paints hand rubbing is impractical, if not impossible. Power buffing is at least a 2-stage process, consisting of buffing or “cutting” with an abrasive compound, followed by polishing (sometimes called “sealing”) with a much less-abrasive glaze or polish. Either can be applied with a wool/yarn pad or the newer foam rubber style, and either of these is available in a bolton or Velcro attachment to a rubber or plastic backing pad. In either case, coarser pads are used for buffing/cutting, finer ones for polishing. Never use the same pad for both.

 

Although they look the same, metal grinders turn up to 6,000 rpm, while paint buffers should never turn more than about 2,500 (so you don’t “burn” the paint). These days, a very practical style of buffer available from various manufacturers can be easily adjusted (with the orange rotary knob) from slow to faster speeds as you’re working, to fit the application.

 

Although they look the same, metal grinders turn up to 6,000 rpm, while paint buffers should never turn more than about 2,500 (so you don’t “burn” the paint). These days, a very practical style of buffer available from various manufacturers can be easily adjusted (with the orange rotary knob) from slow to faster speeds as you’re working, to fit the application.

 

It takes some practice to learn how much compound to apply (too much, a common problem, just clogs your pad). Bill starts by daubing abrasive rubbing compound on the surface with a brush. Most others squirt or dribble it from a squeeze bottle.

 

Although I readily admit that I’ve consistently had good results for years with Meguiar’s and 3M products, it’s my opinion that most automotive polishing products are snake oil. There’s always some new latest, greatest thing and something else that claims to be better. Ask your paint store what the pros prefer. Test different products to see which work best for you. While most compounds and glazes come in (or can be put in) easy-to-apply pour bottles, as seen elsewhere in this book, Bill prefers to mix his own to a thick, brush-on consistency.

 

Start with your buffer on a low speed, so you don’t fling the compound all over, holding it fairly level to the surface, to start working the compound into the paint. Then increase speed as you move the buffer back and forth. If you’ve done your color sanding adequately, the shine should come up quickly, as you can see.

 

Bill obviously knows what he’s doing. Watching a deft rub-out guy do his thing is almost like watching a ballet. To a point, the more you buff, the more it shines. But you have to keep the pad moving constantly, cut with the leading edge, and know when to stop and add more compound to the next area. The cutting pad does generate heat, which can bubble or even burn the paint (turn it brown) if you stay in one area too long, press too hard, or run it too fast.

 

After a few passes back and forth one way, then the other, you should get a shine like this right away. Oh…this is what all that work was for!

 

The buffer is even more dangerous than color sanding on or near peaks, ridges, or edges. Here Bill shows how to buff up to a painted peak, without buffing on it.

 

Add compound and buff about a 4 to 6 sq. ft. section at a time, primarily so the compound doesn’t dry out. But this is also good advice for beginners—take it slow and a little at a time until you start to feel comfortable with the buffer. And even then (maybe especially then) be careful—one bad “bite” from the buffer can ruin the paint.

 

Then again, if a big black bug lands in one of your clear coats, or some other nasty dirt somehow gets in it, you’re not going to be able to just rub it out. You’re going to have to sand it down, spray some more color in that area (if not the whole car), and reclear it. But we’ve said this all along: with lacquer or catalyzed paints, if you screw something up, let it sit overnight, sand it the next morning, and start again where you left off. That’s the thing about doing it yourself—if you do it once, you can do it again…and probably learn to do it better the second time.

The same goes for the rub out. It scares many amateur or first-time painters. People tell them, “You can ruin the whole paint job if you buff through it.” Don’t worry. We show you how to buff so you don’t burn, blister, or bubble the paint.

But there’s always a chance you might rub or sand through a paint layer, either because you rubbed too hard or too much, or because you didn’t put enough paint on in the first place. No big deal. Put some more paint on (a little more than last time, right?), and start the buffing process again, with a more experienced hand this time.

 

Always remember that the buffer turns clockwise, and the outer edge moves the fastest. Here Bill demonstrates his axiom, “Buff off the edge”; meaning, the edge of the pad contacting the paint is moving away from (off) the lip of the hood. Another way he states it is, “Never cut towards, always away.” That buffer has a lot of torque; if you ever “catch an edge” with it, you’ll find out.

 

Here’s another secret I’d never seen before: After adding compound to an area, Bill spritzes it with a little water from the spray bottle. This somehow keeps it from flying off in all directions when he starts buffing it. Also notice that he’s put a liberal dose of compound on this slightly rougher area, and is using the outer edge of the buffing wheel, along with some pressure, to aggressively smooth down the paint. This is possible, but experience teaches you how aggressive you can be.

 

Your buffing wheel eventually loads up with rubbed-off paint and compound, and must be cleaned several times during a job. Bill is using a special spur-wheel made for this, as he spins the buffer; however, a wide screwdriver blade works nearly as well. On foam rubber pads, use a hair brush or your air nozzle to clean it.

 


This tech tip is from the full book, HOW TO PAINT YOUR CAR ON A BUDGET.
For a comprehensive guide on this entire subject you can visit this link: LEARN MORE ABOUT THIS BOOK HERE

 

SHARE THIS ARTICLE: Please feel free to share this article on Facebook, in Forums, or with any Clubs you participate in. You can copy and paste this link to share: https://musclecardiy.com/bodywork/automotive-painting-guide-final-finishing/

 

 

 

 


 

 

You can power-buff areas like the concave dip in this hood if you do it care-fully and gingerly, going slowly to start, and being very careful not to buff directly on the raised edge, on either side.

 

This is a “don’t do this at home” photo. Only a very experienced buffer should ever tip the pad on edge like this (Bill is buffing the hood edge closest to him, so the wheel is turning towards him, off the edge). If you don’t know what you’re doing, this trick could burn a hole through the paint in seconds.

 

With the hood buffed, Bill is going to start on the cowl and front fender. He’s run one large piece of tape along the edge of the hood so he won’t catch it with the buffer. Another smaller one covers the seam between hood and cowl, because he’ll have to buff across both at once. When you’re done power buffing, pull the tape and rub the edges by hand if they need it. But they probably won’t need much.

 

The sharp peak in the middle makes buffing the fender on this Pontiac difficult. Here Bill is buffing the fender up to the taped edge of the hood. Next he’ll tip the buffer the other way and buff up to the fender peak, without getting on it.

 

In general, the rub out not only won’t “ruin” your paint job, it allows you to turn out a top-quality paint job in your garage, at home, without needing a professional spray booth.

Here’s a tip for beginners: since the color sand and rub out proceeds in steps, be conservative. It’s easier to rub a little more paint off later than it is to put more paint back on. This also raises the issues of time and shrinkage. In the case of older lacquer paint jobs, you needed to let the paint sit and shrink for at least a couple of weeks before rubbing it out, and it usually needed another rub out about six months later because it would continue to shrink, including primer layers, at least that long. Modern catalyzed paints do not shrink nearly as much, though shrinkage is always a concern to some extent, especially after the painted vehicle has been out in the hot sun a few times. So this is another reason to make sure you put enough paint or clear on the car—you might very well want to rub it out again after six months or a year, or more.

On the other hand, some types of urethane clears chemically harden so much that they become very difficult to buff to a shine, after color sanding, even with a power buffer and cutting pad. These clears must be sanded and buffed within two or three days of being sprayed, before they fully harden. Check with your paint dealer about this when selecting and purchasing the clear for your paint job.

 

In the text we say to thoroughly wash all surfaces to remove any traces of compound before starting the glaze step. That’s best. But since he keeps things pretty clean as he goes, and he’s working inside the shop, Bill wipes the surface of the hood with a static brush to remove any residue.

 

For the glaze/polish, Bill uses a foam pad on a Velcro backing. Whether foam or wool, polishing pads are finer and softer than cutting pads, so you need at least one of each. Whether you use foam or wool for either is your personal choice.

 

Again, Bill likes to apply his special-mixed glaze with a brush. The key here is to be sparing—it doesn’t take much; using too much just gunks up the surface and the pad.

 

You might have thought the paint looked nice and shiny in the prior pictures, but I think even these photos show the magical difference the glaze makes.

 

Before we finish, anyone rubbing out paint should know about these relatively new mini-buffing pads, again available at your automotive paint store. They mount on a 1/4-inch drive mandrel, which can be used with a drill motor (variable speed is preferred) or with an air-drive right-angle die grinder to get into tighter spots (but be careful to limit RPM). The lighter colored pad is for compound buffing, while the yellowish one is for glaze polishing. They are excellent for buffing in small areas, such as between louvers (as shown) or on a dashboard, where a full-size buffing pad not only wouldn’t fit, but could be dangerous.

 

You saw the orange peel in the clear coat in the opening photos. Now look at how clearly you can see the objects against the shop wall reflected in the hood. And this, believe it or not, is just the beginning of a Bill Larzelere rub-out. Now he’ll spend considerably more time with even finer secret hand-rubbing glazes to make the finish “crisper.” Like most steps in this book, all it takes is your time and patience, which is free. The satisfaction with a beautifully finished job is priceless. The best part about this final step is that it doesn’t really cost anything other than a little polishing compound and a few sheets of sandpaper—plus your free time and effort. Yes, you can do all of this, and be proud of it.

 

In any case, most of the modern paints—especially clears—are nearly impossible to hand rub. They need to be sanded with successively finer grits of “ultrafine” paper—from 1000 to as fine as 2500 grit—and then power-buffed with compound, followed by power-polishing with a glaze.

All color sanding should be done wet, preferably with a rubber pad behind the paper. It is imperative to keep the water, paper, and surface clean of any dirt or particles that can scratch the surface. Since you can’t see what you’re doing while the surface is wet, keep a squeegee or chamois handy to wipe the water off to see how your sanding is progressing. It’s easy to see where you need to sand more once you wipe it dry; sand only enough to make the surface look uniform—don’t oversand at any stage. When you progress from one grit of paper to another, and after each buffing session, thoroughly wash the surface with clean water to remove any traces of the rougher grit or compound.

Other tips and tricks are shown in the photos. But there really isn’t a whole lot of science or magic to any of this whole process. It’s mostly perspiration and patience. The magic is when you finally, after all this work, get to the stage when that amazing gloss comes up after a few passes with the polishing buffer. You might think the main reason you’re doing this is to save a few thousand dollars. But that’s not half as good as being able to lean back against that glass-smooth, deep-gloss paint on you car at the drive-in, gas station, or car show and say with well-deserved pride, “Yes, I did this myself.”

 

Written by Pat Ganahl and Posted with Permission of CarTech Books


This tech tip is from the full book, HOW TO PAINT YOUR CAR ON A BUDGET.
For a comprehensive guide on this entire subject you can visit this link: LEARN MORE ABOUT THIS BOOK HERE

 

SHARE THIS ARTICLE: Please feel free to share this article on Facebook, in Forums, or with any Clubs you participate in. You can copy and paste this link to share: https://musclecardiy.com/bodywork/automotive-painting-guide-final-finishing/

 

 

 

 


Filed Under: Bodywork

Copyright © 2025 · News Pro Theme on Genesis Framework · WordPress · Log in